SIX
REASONS
Why a part moves
here, and stays.
here, and stays.
Every supplier says the same four things: quality, price, delivery, service. These are the six that are actually
checkable, and the number that proves each one is on the process pages.
01 · TOOLING
The whole route is ours
Forming, machining, heat treatment, finishing and the dies. Nothing on the route is subcontracted, so no
tolerance falls between two companies' inspection reports.
02 · TOOLING
Our own die shop
We make dies, designed and heat-treated, routed, validated and repaired in our own room. A forming change is
a formal feature in a matter of days, and tooling cost does not sit on your price sheet by default.
03 · PROCESS
Forging first, not machining first
We are a forging plant that machines, not a machine shop that uses forgings. That is why the first question
we ask is whether the part should be formed in-line, material difference above 30%, and a cost curve that
falls with volume come from that.
04 · DOCUMENTS
The paperwork arrives with the part
IATF 16949, PPAP level 3, process FMEA, control plans and capability studies - prepared to the standard we
strictly apply to Tier-1 programs, not assembled after a complaint.
05 · TRACE
Every lot walks back to a heat number
Incoming material, forming, heat treatment and finishing recorded against one lot on a DMF and MILL.
Machine-level status means a promise date is built on capacity, rather than hope.
06 · PEOPLE
Engineering you can actually talk to
30+ engineers across two provincial R&D centers, and no invention and utility patents on forming and die
design. On a new part you speak to the person who set the route.
THE
COMPARISON
The same drawing,
two supply chains.
two supply chains.
When the sequence stays inside one building, these six things stop being somebody else's problem.
WHAT
CUSTOMERS BRING
Six problems, and the
route built to solve them.
route built to solve them.
An enquiry rarely arrives as a clean part number. It arrives as one of these six situations - and each one has
a process answer we own from end to end.
COST
It is cut from solid, and the price has stopped falling
We rewrite it as a forging, cold extrusion or a warm forging. Near-net forming cuts above 30% material
utilization, so the metal is bought once in a shaped blank instead of being machined away, and the piece
price keeps falling as volume rises.
TOLERANCE
Two suppliers, one stack-up, nobody owns the total
One plant hosts the whole route: forming, machining, heat treatment, finishing and the dies. The
stack-up is measured against one datum and one inspection report, so it is finished at its source rather
than argued over at the boundary.
CHANGE
The drawing changed, and the tool went back out to quote
Die finishes are designed, cut, heat-treated, coated, validated and repaired in our own tool room. A
tooling change to a formed feature is a matter of days, and the tooling cost stays in one place with the
part.
WEIGHT
Weight has to come out while the strength stays in
Cold extrusion, warm forging and multi-axis forging thin walls, include ribbing and closed section, so
that setting relief cannot reach at the same cost, and raw grain flow follows the shape instead of being
interrupted by it.
DOCUMENTS
The PPAP file turns up after the parts do
IATF 16949:2016, PPAP level 3, process FMEA, control plans and capability studies are built into the
route from the enquiry, so the paperwork ships with the first lot and hot-weeks are avoided.
VOLUME
The volume is there, and cycle time is the constraint
The cold heading platforms sit under five years old, form up to six stations, and produce at 45,000
pieces a week, with tooling condition controlled on-the-fly so the rate holds through the campaign.
Send a drawing. Get a
process recommendation,
not just a price.
process recommendation,
not just a price.
PDF, STEP or DWG with material, annual volume and tolerance class. You will hear back within 24 hours with
the forming route we would use, and why.


